How Do You Install A Kitchen Faucet With Side Sprayer??

standard spout faucets

  • Step 1: TURN OFF WATER.
  • Step 2: CONNECT SUPPLY LINES TO FAUCET.
  • Step 3: APPLY SEALANT AND POSITION FAUCET.
  • Step 4: SCREW ON MOUNTING NUTS.
  • Step 5: CONNECT SUPPLY LINES TO SHUT OFF VALVES.
  • Step 6: APPLY SEALANT TO SPRAYER BASE.
  • Step 7: SCREW IN MOUNTING NUTS.
  • Step 8: SCREW IN THE SPRAYER HOSE.

How do you take apart a Moen kitchen faucet?

How to Disassemble a Moen Kitchen Faucet

  1. Locate the setscrew in the handle.
  2. Pry off the cap on top of the handle with a screwdriver to expose the screw, if necessary.
  3. Unscrew the set screw in the handle.
  4. Lift off the handle, exposing a round stainless cartridge collar with an indent that points up.
  5. Remove this cartridge collar by pulling up on it manually.

How do you replace a Moen kitchen faucet sprayer hose?

1:49

4:07

Suggested clip · 82 seconds

Kitchen Faucet Hose Replacement – Moen Pulldown Spray Hose

YouTube

Start of suggested clip

End of suggested clip

How do I install a new kitchen faucet?

Install the New Faucet

  • Place the rubber or plastic gasket, or trim ring, over the faucet holes in the sink and set the deck plate.
  • Feed faucet lines into the hole(s).
  • Install washers and nuts underneath the sink.
  • For pull-down faucets, attach the quick-connect hose to the supply pipe.
  • Connect water supply lines.

Can I add a sprayer to my kitchen faucet?

Adding a Sprayer to Kitchen Faucets. It is actually more economical to add a sprayer than it is to install a whole new faucet with a sprayer spout. This installation project should not take more than an hour. Check your sink to ensure that it has an extra hole near the faucet before you begin.

How do you install a peerless kitchen faucet sprayer?

Suggested clip 108 seconds

How to Install a Peerless Single Handle Pulldown Kitchen Faucet

YouTube

Start of suggested clip

End of suggested clip

How do I change a Moen kitchen faucet cartridge?

0:24

2:23

Suggested clip 79 seconds

Moen 1225 Replacement – YouTube

YouTube

Start of suggested clip

End of suggested clip

How do you take the handle off of a Moen faucet?

Some Moen faucets have handles that remove by loosening the screw in the back of the handle. To loosen this screw use a 3/32″ hex wrench. After the handle has been removed unscrew the spout collar nut by turning counterclockwise then lift and rotate the spout.

How do I find my Moen faucet model number?

The model/series number is usually a four or five digit number beginning with “7” or “8” and may be followed by letters. The series number may sometimes be found on the underside of the spout. The series number is often found on the back of the decorative ring located at the bottom of the spout.

How do you fix a Moen kitchen sprayer?

How to Fix a Moen Kitchen Sink Sprayer That Is Stuck On

  1. Shut off the water supply to kitchen faucet.
  2. Pry off the covering with a standard screwdriver to access the switch parts underneath.
  3. Spray the parts thoroughly with a petroleum-based lubricant.
  4. Clean the parts with a can of compressed air.
  5. Snap the covering back over the switch parts.

How do you remove a Moen kitchen faucet sprayer?

How to Remove the Sprayer on a Moen 7900 Faucet

  • Turn off the valves under the sink by rotating the valve handles counterclockwise.
  • Hold the hose in one hand and push upward on the hydrolock connection with the other to disconnect the sprayer from the diverter.
  • Pull the sprayer straight upward and out of the guide.

Why is my Moen kitchen faucet leaking?

Water Leaking Due to Worn O- Ring

There are generally two causes of water leaking from your Moen faucet. Because pull-out spray faucets have a single handle, the most common cause of the water leaking is the O-ring. To replace the O-ring, turn off the water to the faucet from below the counter.